pumpcalc

Water Hammer Pressure Calculator

Work out the pressure surge when a valve closes or a pump trips and the flow suddenly stops. Enter the pipe and the velocity change — the calculator gives the wave speed, the Joukowsky surge pressure and head, and the critical time that decides whether the full surge actually happens.

Units:
Sets the pipe elastic modulus. Pick Custom to edit it.
Bore, not outside diameter.
Must be less than half the diameter.
Water at 20 °C is about 2.2 GPa.
Flow velocity stopped (or started) by the valve or pump trip.
Length from the valve to the reservoir or dead end.
1.0 for an anchored pipe. About 0.91 for a steel pipe free to move axially (1 − ν², ν = 0.30).

Joukowsky gives the theoretical maximum surge for a rapid maneuver — a valve closure (or pump trip) faster than the critical time below. A slower maneuver gives a smaller surge.

Pressure-wave speed
1333 m/s
= 4373 ft/s
Pressure surge Δp
2.665 MPa
= 26.65 bar = 386.6 psi
Surge head ΔH
271.8 m
= 891.7 ft
Critical time T_c (wave round trip)
0.7503 s
Close the valve slower than this and the peak surge is lower than the Joukowsky value above.

Formula

a=K/ρ1+KE⋅De⋅c1Δp=ρ⋅a⋅ΔvΔH=a⋅ΔvgTc=2Laa = \sqrt{\frac{K/\rho}{1 + \frac{K}{E} \cdot \frac{D}{e} \cdot c_1}} \qquad \Delta p = \rho \cdot a \cdot \Delta v \qquad \Delta H = \frac{a \cdot \Delta v}{g} \qquad T_c = \frac{2L}{a}

SymbolMeaningUnit
ΔpPressure surge (Joukowsky)Pa
ΔHSurge headm
aPressure-wave speed in the pipe (Korteweg)m/s
ρFluid densitykg/m³
ΔvVelocity change — flow velocity stopped or startedm/s
KFluid bulk modulus (water at 20 °C ≈ 2.2 GPa)Pa
EPipe elastic modulusPa
DPipe internal diameterm
ePipe wall thicknessm
c₁Restraint factor: 1.0 anchored, 1 − ν² free to move axially—
LPipe lengthm
T_cCritical time — wave round trip, 2L/as
gStandard gravity, 9.80665 m/s²m/s²

The Joukowsky surge is the theoretical maximum, reached only when the maneuver is fast — closure (or trip) time at or below the critical time TcT_c. If the valve takes longer than TcT_c to close, the reflected wave arrives while the valve is still closing and the peak is lower; that case needs the Allievi method or a numerical transient simulation. The Korteweg wave speed is lower in flexible pipe: steel runs about 1000–1400 m/s, HDPE only about 250–350 m/s, so the same velocity change gives a much smaller surge in plastic pipe.

Worked examples

Example 1 — SI: 6 in Sch 40 steel pipe, 500 m long

Example 2 — US: same pipe

(The US inputs are rounded — 4411 ft/s and 6.56 ft/s — so the exact head is 899 ft, shown as 900 ft.)

Assumptions and limits

Next step

Velocity change drives the surge — check the flow velocity in your pipe: Pipe velocity calculator

FAQ

Why is the Joukowsky value a maximum, not the exact surge?

Joukowsky assumes the velocity change happens instantly, before the pressure wave can travel to the far end of the pipe and back. That is true only when the maneuver is faster than the critical time T_c = 2L/a. A slower closure lets the reflected wave arrive mid-stroke and cancel part of the rise, so the real peak is lower. Friction, air and pipe aging also reduce it.

What is the critical time, and why does it matter?

The critical time T_c = 2L/a is how long the pressure wave takes to travel to the far end of the pipe and return. Close the valve in less than T_c and the full Joukowsky surge develops. Close it slower and the peak falls — roughly in proportion to T_c divided by the closing time for a linear closure. Long pipes have long critical times, so even a "slow" valve can be fast relative to T_c.

How does pipe material affect water hammer?

Through the wave speed. A stiff pipe (steel, E = 200 GPa) barely yields to the pressure wave, so the wave travels fast — about 1344 m/s in the worked example — and the surge is large. A flexible pipe (HDPE, E ≈ 1 GPa) stretches and absorbs the wave, dropping the speed to roughly 250–350 m/s and cutting the surge to about a quarter. That is why plastic pipe is far more forgiving of fast valve closures.

How do I reduce water hammer in an existing line?

Slow the maneuver down past the critical time (slow-closing valve or controlled pump coast-down), reduce the velocity change (lower flow velocity or a larger pipe), or add surge protection (surge vessel, air chamber, or relief valve). The cheapest fix is usually a slower actuator — but check the new closing time against T_c first, because a valve that is still fast relative to a long pipe will not help much.

Does air in the line make water hammer better or worse?

Entrained air makes the fluid more compressible, which lowers the wave speed and the Joukowsky surge — so a bubbly line usually sees a smaller peak. But a trapped air pocket at a high point is different: it can compress and then drive a secondary surge, and it can cause column separation on pump trip. Do not rely on air as protection; vent high points and size protection for the air-free case.

Sources

Related: pipe pressure drop calculator — friction loss in the same line, for the steady-flow side of the design.

For preliminary estimates only. Verify against manufacturer data and the governing standard before purchase or installation.

Reviewed by pumpcalc · Last updated 2026-11-18