Pipe Velocity and Size Calculator
Find the mean velocity in a pipe from the flow and the inside diameter — or work backwards and size the pipe for a target velocity. The calculator also tells you whether the velocity sits in the usual range for suction lines, discharge lines or general process water.
| Quantity | Value |
|---|---|
| Flow area | 0.007854 m² |
| Velocity head (v²/2g) | 0.1594 m |
Formula
| Symbol | Meaning | Unit |
|---|---|---|
| v | Mean flow velocity | m/s |
| Q | Volumetric flow rate | m³/s |
| A | Pipe flow area | m² |
| D | Pipe inside diameter | m |
| v²/2g | Velocity head | m |
| g | Standard gravity, 9.80665 m/s² | m/s² |
The second line is the first one rearranged: pick the velocity you want and it gives the inside diameter that delivers it. In US units the same relation is often written as .
Typical velocity ranges for water and similar liquids (experience values from several engineering references, not standard limits):
- Pump suction lines: 0.6–1.5 m/s (2–5 ft/s)
- Pump discharge lines: 1.5–3 m/s (5–10 ft/s)
- General process and cooling water: 1–2.5 m/s (3–8 ft/s)
- Above about 3 m/s (10 ft/s), pressure drop, noise, erosion and water-hammer risk all rise.
Worked examples
Example 1 — SI: velocity of 50 m³/h in a 100 mm pipe
- Flow: ; pipe:
- Flow area:
- Velocity:
- 1.77 m/s sits in the usual range for a pump discharge line (1.5–3 m/s).
Example 2 — SI: sizing a pipe for 50 m³/h at 1.5 m/s
- Flow: ; target velocity:
- Required inside diameter:
- There is no 109 mm pipe, so check the nearest standard sizes: a 100 mm pipe runs at 1.77 m/s and a 125 mm pipe at 1.13 m/s. Pick the size whose velocity fits the service — here the 100 mm pipe if this is a discharge line, the 125 mm if it is a suction line.
Example 3 — US: 220 gpm in a 3.94 in pipe
- Flow: ; pipe:
- Velocity:
- 5.79 ft/s sits in the usual range for a pump discharge line (5–10 ft/s).
- Sizing the same flow for a target of 5 ft/s needs an inside diameter of 4.24 in.
Assumptions and limits
- Inside diameter, not nominal size. The velocity depends on the bore the liquid actually flows through. A DN100 pipe is not 100 mm inside — convert the nominal size to the actual inside diameter from the pipe schedule and wall thickness first.
- Mean velocity only. The formula gives the average velocity across the cross-section. The velocity at the pipe centre is higher, and near the wall it is lower — the profile depends on whether the flow is laminar or turbulent.
- The velocity ranges are experience values, not standard limits. Several engineering references agree on them, but no standard fixes them. A viscous liquid, a slurry or a long suction line may need a lower velocity; check the pump manufacturer’s guidance for the service.
- Sizing gives a minimum bore, not a pipe to order. Pick the next standard size at or above the calculated diameter, then re-check its actual velocity — a larger pipe runs slower, a smaller one faster.
- Steady, incompressible flow. The relations are for a constant flow of liquid; they do not cover water hammer or gas flow.
Next step
Velocity settled? Work out what this flow and pipe size cost in pressure drop: Pipe pressure drop calculator
FAQ
What velocity should I design a pump suction line for?
The usual range is 0.6–1.5 m/s (2–5 ft/s). Suction lines run slower than discharge lines on purpose: a low velocity keeps the friction loss in the suction pipe small, which protects the NPSH available at the pump. If the suction velocity is too high, the suction loss eats into the NPSH margin and the pump can cavitate.
What happens if the velocity is too high?
Pressure drop grows with the square of velocity, so doubling the velocity roughly quadruples the friction loss. High velocity also means more noise, more erosion (especially with solids or entrained gas), and a larger water-hammer surge if a valve closes quickly. As a rule of thumb, stay below about 3 m/s (10 ft/s) for water unless there is a specific reason to go higher.
What happens if the velocity is too low?
The pipe is larger than it needs to be, which costs more and takes up more space. In some services a very low velocity also lets solids settle out or lets air collect at high points. For clean water there is no hard lower limit — the suction range of 0.6–1.5 m/s is a practical guide, not a minimum.
Should I use the inside or the outside diameter?
Inside diameter. The flow area — and therefore the velocity — depends on the bore the liquid flows through. The outside diameter is larger, so using it would understate the velocity. If you only know the nominal size (DN/NPS), convert it to the actual inside diameter from the pipe schedule and wall thickness.
Why does the sizing mode give a diameter that does not match any real pipe?
The formula gives the exact bore for the target velocity, and real pipes come in standard sizes. Treat the result as a minimum: pick the next standard size at or above it, then check the actual velocity in the velocity mode. In the worked example, 50 m³/h at 1.5 m/s needs 109 mm — a 100 mm pipe runs at 1.77 m/s and a 125 mm pipe at 1.13 m/s.
Sources
- Engineering Desk Tools, "Pipe Velocity Calculator" — suction 0.6–1.5 m/s, discharge 1.5–3 m/s, general 1–2.5 m/s
- Industrial Engineering Studio, "Pipe Sizing Fundamentals" — same velocity ranges, and D = √(4Q/(πv))
- RedBison, "Pipe Flow Rate, Velocity and Diameter" — the 0.4085 US coefficient; 50 m³/h example: 100 mm pipe 1.77 m/s, 125 mm pipe 1.13 m/s
For preliminary estimates only. Verify against manufacturer data and the governing standard before purchase or installation.