pumpcalc

PN to ASME Class Conversion

Look up the nominal PN for an ASME Class, or the nominal Class for a PN. PN and Class are two separate pressure-rating systems, so this is a table lookup from ISO 7005-1, not a calculation — and a nominal match does not mean two flanges bolt together.

Pick a Class to see its nominal PN.
Pick a PN to see its nominal Class.
Nominal correspondence
Class 150 = PN 20
Nominal only — a matching pair does not mean the flanges are interchangeable.

Correspondence table (ISO 7005-1)

The full nominal correspondence. There is no formula behind these pairs — each row is a name-to-name lookup from ISO 7005-1.

ASME ClassPN (ISO 7005-1)
Class 150PN 20
Class 300PN 50
Class 600PN 110
Class 900PN 150
Class 1500PN 260
Class 2500PN 420

Note: some valve and pipe standards write Class 600 as PN 100 and Class 1500 as PN 250 instead of PN 110 and PN 260. The table above uses PN 110 and PN 260, as in ISO 7005-1.

Often compared but NOT interchangeable

These pairs sit near each other and are often confused in the field, but their flanges have different dimensions and are not interchangeable. Check the actual bolt circle and hole count in the flange compatibility checker before joining anything.

PairWhy not interchangeable
PN16 vs Class 150Nominal neighbours, different flange dimensions.
PN40 vs Class 300Nominal neighbours, different flange dimensions.

Formula

There is no formula. PN and Class are separate rating systems with no linear relationship between them:

PN≠k×Class\text{PN} \neq k \times \text{Class}

The table below the tool is a nominal correspondence from ISO 7005-1: each Class has one listed PN name, and that is the whole conversion. Do not scale, interpolate, or extrapolate between rows — a Class that is not in the table has no nominal PN value.

Worked examples

Example 1 — Class 150 to PN

Class 150 is nominally PN 20. That says nothing about whether a PN 20 flange bolts to a Class 150 flange — it does not, in general.

Example 2 — Class 300 to PN

Class 300 is nominally PN 50.

Example 3 — Class 600 to PN

Class 600 is nominally PN 110. Note that some valve and pipe standards write Class 600 as PN 100 instead — same Class, different naming convention. This page uses PN 110, as in ISO 7005-1.

Example 4 — PN 20 to Class

PN 20 is nominally Class 150. The reverse lookup gives the same pair as Example 1, as it should: the correspondence runs both ways.

Assumptions and limits

Next step

Got a pair in mind? Check whether the flanges actually bolt together: Flange compatibility checker

FAQ

Why is there no formula for converting PN to Class?

Because PN and Class are two separate rating systems, not two units of the same quantity. A formula would need a fixed ratio between them, and none exists — the pairs are assigned by standard, not derived. ISO 7005-1 simply lists which PN name goes with which Class, so the conversion is a table lookup.

Can I bolt a PN16 flange to a Class 150 flange?

No. PN16 belongs to the EN 1092-1 series, while Class 150 is ASME B16.5, and their flange dimensions differ — different bolt circles, hole counts, and hole sizes at most sizes. PN16 and Class 150 are only nominal neighbours, not interchangeable parts. Use the flange compatibility checker to compare the actual dimensions for your size.

Why is Class 600 sometimes written PN100 and sometimes PN110?

Two naming conventions exist side by side. ISO 7005-1 lists Class 600 as PN 110 (and Class 1500 as PN 260), while some valve and pipe standards write the same Classes as PN 100 and PN 250. Both refer to the same Class; the difference is which standard the part was named under. Check the standard on the part or drawing before ordering.

Does PN20 mean the flange is rated for 20 bar?

No. In this table PN is a nominal designation, not a pressure in bar. The allowable pressure for a given PN or Class depends on the material and the temperature — a carbon-steel flange and a stainless flange with the same Class rating have different pressure–temperature limits. Always check the rating table for your material and temperature.

Can I use this table for EN 1092-1 PN flanges?

No. EN 1092-1 uses its own PN series — 6, 10, 16, 25, 40, 63, 100 — which is a different set of sizes from the ASME metric PN values in this table (20, 50, 110, 150, 260, 420). A PN16 EN flange and a PN20 ASME-named flange are not the same thing, and neither is interchangeable with Class 150.

Sources

For preliminary estimates only. Verify against manufacturer data and the governing standard before purchase or installation.

Reviewed by pumpcalc · Last updated 2026-11-17