NPSH Available Calculator
Work out the net positive suction head available at a pump inlet — the margin between the suction pressure and the liquid’s vapour pressure, expressed as a head. If it falls below what the pump requires, the pump cavitates.
Next step: Pump power calculator →
Formula
| Symbol | Meaning | Unit |
|---|---|---|
| NPSHa | Net positive suction head available | m |
| p_abs | Absolute pressure at the suction liquid surface | Pa |
| p_v | Saturation vapour pressure at the liquid temperature | Pa |
| ρ | Liquid density | kg/m³ |
| g | Standard gravity, 9.80665 m/s² | m/s² |
| h_s | Suction height — liquid surface above the pump centreline is positive | m |
| h_f | Suction line loss | m |
The first term is the pressure head at the liquid surface above vapour pressure. A flooded suction (liquid above the pump) adds head; a suction lift subtracts it; friction in the suction line subtracts further. Enter the temperature and the calculator fills in vapour pressure and density from the water table — override either field for another liquid.
Worked examples
Example 1 — SI: suction lift, water at 20 °C
- Water at 20 °C: ,
- , ,
The pump must lift water 3 m, so the available suction head is 6.11 m.
Example 2 — SI: flooded suction, water at 80 °C
- Water at 80 °C: ,
- , ,
Hot water has far less NPSHa than cold water in the same layout: vapour pressure eats 4.97 m of head at 80 °C, against 0.24 m at 20 °C.
The table value is rounded: the IAPWS-95 value this calculator uses at 80 °C is 47.42 kPa (47.4158 kPa), a 0.01% difference that leaves the result at 7.16 m.
Example 3 — US: the same suction lift in feet
- The same case as Example 1: , , ,
- Pressure head above vapour pressure:
That is the same 6.11 m as Example 1, allowing for rounding.
Assumptions and limits
- Water properties, 0–100 °C. Vapour pressure and density are auto-filled from the water table at the temperature you enter. For another liquid, override both fields with its vapour pressure and density at the pumping temperature.
- Absolute pressure, not gauge. The suction surface pressure is usually atmospheric pressure: 101.325 kPa at sea level, lower at altitude. Enter the local absolute pressure at the site.
- Suction loss is an input, not computed here. Estimate from the suction piping (friction and fittings) — see the total dynamic head calculator — and enter it.
- Steady, incompressible, liquid-full suction line. Velocity head at the liquid surface is taken as negligible. The formula does not cover transient or surge effects, dissolved gas coming out of solution, or two-phase flow.
- NPSHa is a system property; NPSHr is a pump property. Compare them only at the same duty flow, with NPSHr read from the pump curve.
- No universal margin is stated on this page. How much NPSHa should exceed NPSHr has no verified common value — follow the pump manufacturer’s recommended margin.
Next step
Once the suction checks out, work out the power the pump needs: Pump power calculator
FAQ
What is the difference between NPSHa and NPSHr?
NPSHa is what the suction system delivers: the pressure head at the pump inlet above vapour pressure, from the layout, the liquid and the site. NPSHr is what the pump needs at a given flow, read from the manufacturer’s pump curve. The pump runs without cavitation only when NPSHa exceeds NPSHr — and by whatever margin the pump manufacturer recommends.
Why does hot water cavitate more easily than cold water?
Vapour pressure rises steeply with temperature: water at 20 °C has p_v = 2.34 kPa, at 80 °C it is 47.4 kPa. The (p_abs − p_v) term shrinks, so NPSHa falls even if nothing else in the suction line changes. Hot-water and boiler-feed pumps therefore need a flooded suction or a pressurised source to keep NPSHa up.
How does altitude affect NPSHa?
The suction surface pressure is usually atmospheric pressure, and atmospheric pressure falls with altitude — so p_abs is lower than the sea-level 101.325 kPa and NPSHa drops by the same head. Enter the local absolute pressure at the site, not the sea-level value.
How much margin should I allow above NPSHr?
There is no verified universal margin value, so this site does not state one. Follow the pump manufacturer’s recommended margin for the pump and duty.
What does a negative NPSHa mean?
The liquid would flash to vapour at the pump inlet before the pump can do any work — the pump cavitates and cannot deliver its rated head. Raise the liquid level, shorten or enlarge the suction line to cut h_f, cool the liquid, or raise the suction pressure.
Sources
- Firgelli “NPSH Calculator” formula page
- processconvert “NPSH Available” — NPSHa = Ha + Hs − Hv − Hf
- Water vapour pressure and density at temperature — see the water vapor pressure and density table on this site
For preliminary estimates only. Verify against manufacturer data and the governing standard before purchase or installation.